How to Find the Right HID Xenon Lamps

HID xenon Lamps are able to work for 3000 hours. When it is time to replace these bulbs, drivers will have to examine the many varieties of xenon bulbs for sale.
The price and selection of replacement xenon bulbs also varies quite considerably depending on where you buy them from, be it the a main dealer, a high street accessory shop or an internet specialist.
HID Xenon Lamps - Choosing the right colour
When buying new xenon bulbs you may have noticed that they have different colour temperatures listed next them, for example 6000k, 8000k or even 140000k. The K stands for Kelvin and it is the unit used to measure the colour emitted by xenon bulbs.
Often for those who have never used this type of bulb it can be confusing to understand what the different ratings mean. Commonly it is thought that 14000K or the other choices mean the heat which is emitted by the HID Xenon Bulb rather than the colour. The 14000K bulb is not going to be hotter than the 6000K bulb.
Colour temperature is rated from 4000K to 14000K. The colours the bulbs will be are listed below, since each bulb will have a different colour.
* 4000k - white light with a yellow tint
* 6000k - Completely white
* 8000k - white light with a blue tint
* 12000k - Mild purple in the white light
Unfortunately buying xenon bulbs on the basis of colour is not straight forward, as the higher the colour temperature of a xenon bulb the less light it will actually emit from your headlights. This effect is barely noticeable for bulbs in the 4000k to 8000k level however at bulbs rated at 12000k and higher the drop off in terms of light emitted is quite marked.
The light output is measured in lumens (lm). A new vehicle will have xenon bulbs rated at 4300K with a light output of 3200lm. 12000K bulbs have 2,200lm, which is 1,000lm less light being provided. If you do want a deep purple bulb to enhance the look of your vehicle you have to be concerned with the light emission you receive.
Buying HID xenon bulbs can be quite expensive unless you shop around. With the amount of online car bulb shops you are able to find a significantly lower cost for light bulbs than before.
For instance, if you purchase the E1 approved bulb such as the Orsam Xenarc you might find the cost is 200 from a manufacturer. The same bulb could be found online for 70 as the internet site is normally a specialist in car bulb replacement.
HID xenon bulb replacement can be difficult for someone who is not used to the system operation. There are high voltages behind the connector. It is best to seek a professional mechanic with electric qualifications to avoid the potential shock, which could blow the new light bulb you are trying to install.
If you are looking to change your Headlight Bulbs then the different choices and types available can be quite daunting. However, buying the right set of Xenon Bulbs that are suited to your car will make driving in the dark safer, enjoyable and less stressful.

LED Solar Street Light Projects

LED Street lighting is a fresh new alternative to traditional street lamps such as LPS, HPS, or MH street lights. LED lighting provides a multitude of advantages over conventional incandescent light: LED street lights are environmentally friendly, energy efficient, and cost-effective. This smart, "green" option for outdoor lighting has emerged on the green scene due to the recent technological advancements of LED illumination.
But more "greener" option for you is Solar street lighting by recycled green energy lighting system. They are of energy saving and environmental friendly, which can be used for residential, road, park and so on. High quality solar panel absorbs sunlight and convert into electricity energy, then charges maintenance-free battery and finally LED street lights automatically when day off, auto-off when day break.
The working method of solar street lights is: solar panel absorbs sunlight and converts it to electricity to drive 60W LED Street light.
The whole system is mainly composed by:
60W LED street lighting, solar panel, lead acid battery and solar street lighting controller, pole (suggest 6-8m height).
Because of different weather condition in different country and different requirements from different market, so the specification of each part of the whole solar street lighting system, especially solar panel and battery, are depending on following factors:
? Average local daily sunshine hours.
? Working times of the system per night.
? Backup days of the solar system during rainy days.
Advantages of LED Solar Street Lighting Projects
1). Lower power consumption
2). Higher power, higher intensity
3). Save all your electricity cost. Save electric transformer and cable cost. Free maintenance
4). Environmental Impact - Eliminate Hazardous Disposal
5). Longer lifetime: Lifespan of solar panel is 20-25 years. Lifespan of LED street lighting is 6-8 years. Lifespan of battery is 4-6 years.

How To Decorate With LED Tube Lights

LED tube lights have quickly become a very popular way of decorating a room, outdoor living space, RV, and business. There are plenty of different reasons for this. The main reason being that they use much less energy than traditional light bulbs. Following that reason is the fact that these tube lights can be purchased in many different colors and lengths.
These LED tube lights are also flexible so that they can be configured into many different shapes and wrap around corners. This means that the decorating possibilities are almost endless with these LED lights. For anyone who is looking for a great way to add a splash of color, a sense of style, and are able to do it quickly and easily, here are some ideas in helping you use these LED lights.
One thing to keep in mind when working with LED tube lights is that they must be hung with small clips that are screwed to the wall. Before you begin to drape the lights along your wall, your counter, your awning, or wherever else you want to place them, make sure to plan out where he hooks will go.
People routinely use the LED tube lights as an outline for something larger, or they want to draw attention to. This means that the tube lights will be fashioned to look like a circle, square, or some other shape. To do this, you only need to set the hooks in the outline of the shape you want.
LED tube lights also need to be near an outlet for power. When decorating keep in mind that there will a cord that either needs to be hidden, or kept close to an outlet. You can hide these easily by running them along the baseboard or using a plastic conduit.
LED lights can be somewhat bright when there are a lot of of them being used. A tube light, or a 'rope light' contains several feet of LED lights can create an atmosphere where it is too bright to sleep. When using this type of decoration, you will also want a way to unplug them or turn them off. It is not a good idea to put the plug behind heavy furniture in the attempt to hide it. If in the bedroom, you may regret that decision as you pull out the dresser in the middle of the night so you can sleep.

Factory to produce innovative composite materials opens in Yakutia

The factory of innovative composite materials based on continuous basalt fiber opened in Pokrovsk, the administrative center of the Khangalassky district of ??Yakutia. In accordance with "Basalt - New Technologies" project, the factory will produce four types of products using nanotechnologies.
It goes about basalt-concrete constructions for industrial and civil construction, basalt-plastic building bars and the mesh for reinforcement of roadway. The continuous basalt fiber will also be produced: the fiber is the feedstock for the production of many composite materials. Common rocks of magmatic origin are used as the main raw material for basalt fiber.
Composite products based on basalt possess high corrosion and chemical resistance. They retain their strength at low temperatures and hold heat very well. This makes them indispensable in road and housing construction in the Far North, under permafrost conditions, where conventional materials can not withstand extreme seasonal changes in temperature, reaching 100 degrees in Yakutia.
The Innovative technologies that are used at the new factory were developed together with experts of RUSNANO. According to company director Yegor Zhirkov, the products on the basis of continuous basalt fiber can be used in the automotive, oil and gas industry, agriculture and many other industries. For Yakutia, it is most important to obtain the materials needed for construction. This will greatly reduce the cost of purchase and delivery of expensive steel reinforcement bars, reinforced concrete and other building materials that are delivered from outside the republic.
The project will create more than 260 additional jobs in the Khangalassky region of the republic. Yearly tax revenues from the new production in the budget of Yakutia are expected to amount to 430 million rubles.
Related products recommended:

Twill Carbon Fiber Hybrid Fabric

UD S-Fiberglass Fabric

Toray UD Carbon Fiber Fabric

Milled Carbon Fiber

Unidirectional Carbon Fiber Fabric

Cuts Fiber Short

Carbon Fiber Grid

Unidirectional Carbon Fiber Strip

What is Metal Stamping?

Metal stamping is the process of cutting and shaping metal alloys into specific forms, especially to be used as components for large machinery or structures. Metal sheets can be molded into different pre-determined shapes for use as regular products like pans and cans. The most common alloys that are used in metal stamping are steel, zinc, nickel, aluminum and titanium. Metal stamping is a very cost-effective and productive way of producing many kinds of metal products on a large scale.
In metal stamping, the metal sheets are placed in a die or a press tool that has a specially designed cavity that gives the preferred shape to the metal sheet. The upper part of the die connects to the press slide while the lower component connects to the press bed. A specific component known as the punch pushes the metal sheet through the die, thus performing the actual shaping operation. After pressing, the metal is plated with gold, palladium, nickel or tin to prevent corrosion.
Plating also increases the wearability and solderable nature of the product. Sometimes, the sheet is also pre-plated before the stamping process, and then the product is cleaned to remove excess metal stamping oils and films. The product is then heat treated to make it stronger since it is still in the soft state after stamping. The product is then subjected to the deburring process for removing the sharp corners. This is done by using chemicals or abrasives. Metal stamping also involves other metalworking processes like piercing, blanking, forming and drawing on the same machines.
Stamping presses have specific force, speed and precision for giving a specific shape to the metal. There are two types of metal stamping presses: Mechanical and hydraulic. These are available in an extensive range of capacities, sizes, stroke lengths and operating speeds.
Metal stamping is slowly replacing other metal forming processes like die casting, forging, fabricating and machining. One reason for this is the very low costs involved in metal stamping. The dies used for metal stamping cost less than those used in forging and casting. Also, the metals used in metal stamping can be harder than those used in other processes, thus making the end product stronger. The cost of the secondary processes, like cleaning and plating are also considerably reduced.
Moreover, there are certain products that have to be produced only through metal stamping: Base weights, brackets, balance clamps, brake flanges, conveyor flights, bushing seats, engine bases, flywheel shrouds and friction plates. There are also different kinds of metal stamping including: Deep drawn stamping, electronic stamping, Fourslide stamping, medical stamping, progressive die stamping and short run stamping. The most commonly used type is the progressive die drawing wherein a metal sheet is drawn through a series of dies and stamping is done by all the dies simultaneously, thus considerably reducing the time it takes.
Metal Stamping Info provides detailed information about precision, custom, and sheet metal stamping, as well as metal stamping machines and metal stamping die. Metal Stamping Info is the sister site of www.gaogelmetal.net.

A Review of the Collecta Miragaia Dinosaur Model

The Collecta Miragaia Dinosaur Model Reviewed
Fossils of European Stegosaurs are very rare. What fossil material that has been excavated provides evidence of a number of Stegosaur genera from the Jurassic, but most of the specimens are incomplete and highly fragmented. Little is known about the evolution of the Thyreophora (armoured dinosaurs) in Europe. However, over the last few years a number of better preserved and more complete Stegosaur fossils have been discovered in western Portugal. One of these recent fossil discoveries, that of a dinosaur that came to be known as Miragaia has inspired Collecta to make a replica of this armoured dinosaur.
Little is Known about European Stegosaurs
In contrast to most other European Stegosaur remains, much of the front part of the skeleton of this Late Jurassic Stegosaur is known. Paleontologists have excavated at least two specimens, one adult, one sub-adult from the same dig site in Upper Jurassic strata attributed to the Lourinha Formation of western Portugal. Elements of the skull have been discovered and from this scientists have been able to reconstruct this dinosaur. Collecta, the dinosaur model makers, have used the scientific data to produce a colourful, not-to-scale dinosaur model of this Portuguese herbivore.
The First Stegosaur Skull Discovered in Europe
Skull material includes the premaxilla, maxilla and the naris post elements that comprise the back of the skull. Post cranial material comprises of shoulder bones, most of the front legs, neck bones and a number of armoured plates. Miragaia seems to have had a remarkably long neck for a Stegosaur. It had an estimated fifteen cervical vertebrae (neck bones), more than long-necked Sauropods such as Diplodocus and Apatosaurus.
The Miragaia Dinosaur Model
The Miragaia model from Collecta shows this long neck in fine detail. In fact the head and the neck make up about twenty-five percent of the length of the entire model. Scientists have debated how flexible the neck of Miragaia was, ironically the plastic compound used to make this replica has left the model with a rather bendy neck, but this does not detract from the overall quality of the model.
The head is narrow and the front legs are smaller than the hind legs, a trait seen in most other Stegosaur genera. The model has been painted light brown, with a red flash on the throat pouch. The armour plating and the tail spikes are painted in a dark green colour, mimicking the colouration of the top of the spine and down to the tail. The model has two shoulder spikes, these are large, more than two centimetres in length and painted bright red.
Armour Embedded into the Skin
The Miragaia dinosaur model has been given a rough skin texture, to give the impression that this dinosaur had large scales, with some dermal armour embedded along the flanks. Scientists are not sure what the tail of this dinosaur was like. There have been no fossils of the back-end of Miragaia found. The model makers at Collecta have given their replica a row of spines running back from over the hips to the tip of the tail.
The model's overall length is nineteen centimetres approximately,and it is a welcome addition to the Collecta model range, one that will no doubt delight fans of Stegosaurs.
Everything Dinosaur is run by parents, teachers and real dinosaur experts. Visit our website www.everythingdinosaur.com to view the very latest dinosaur and prehistoric animal models.
To learn more about the products and services we offer at Everything Dinosaur visit www.gengudino.com

How Does a Vacuum Packing Machine Preserve Your Food?

Vacuum packing machine is a humble machine that needs a place in your kitchen if you are frequently finding yourself storing foods and worrying about the food getting spoiled. Both dry and moist foods can be stored by removing air and sealing. This kind of package is commonly found in store bought goods that you buy in bags. Vacuum storage was once commercial, but now it has become more affordable with small handy machines that can be used in any home. It doesn't need large counter space and hence storing and handling such devices is quite simple.
Before buying out a vacuum sealing device for yourself, it is better to gain an understanding about how such a device works. The device works by sucking air around the food which is responsible for mold and bacteria to develop. Any living organism needs air to breathe and when air is removed around the food, no tiny organism can live and hence, your food will be free from harmful mold and bacteria. Further, oxidization and other such processes which make the foods go stale occur only when the food items react with air. When there is no air to react, such processes won't spoil your food and hence, the shelf life of the food you store can be greatly increased.
After sealing the food using vacuum food sealer, you need to store them in refrigerator or freezer, otherwise, the food will be spoiled easily. Investing in such a device is quite a reasonable spending because you often end up storing foods and hoping the food to stay fresh. Using such packing technique, moisture in the food can be retained by limiting the amount of air inside the bag. Also, crunchy foods can be stored for several days using this sealing technique and every bite you take will be fresh as new.
Jared Mason talks about food safety using commercial vacuum sealers. Learn more healthful tips on CommercialVacuumSealer.org

Related enterprises recommended:
Company name：Wenzhou Youlian Machinery Manufacturing Co.,Ltd.
Contact us：Phone: 86-577-86139198
　　　　　Fax:86-577-86137798
Web site：http://www.packingmachine.net/
The main products：Linear Filling Machine,Automatic Paste Labeling Machines,Horizontal Packaging Machine,High Speed Capping Machine,

LED Lighting for Your Car

Utilizing LED lighting for your car would actually help you especially at night. You only need to install the lights in order to let other motorists to see you. Usually, the lights change its color brought about by the LEDs or Light Emitting Diodes. LEDs would also help you see during the night if you are planning to travel. You can use them as light strips on the side of your car, on top of the hood of your car or on the windshield. You can also use the LEDS as a stylish way to increase the illumination on the back of your vehicle. You can place it as a third tail light near the bumper. The LED lights can be attached near the bottom in the back of your car in order for it to become unparalleled lights when other motorists are behind your vehicle.
Aside from using it during the night, utilizing led lighting for your car during the day is also a great idea. Most of the time, there would be problems in the road such as sudden breaks especially during traffic. Since the LED lights are hard to miss, motorists would be able to see the light easily. The advantage of the LEDs compared with other types of lighting is that they shine brighter and they light up faster than other bulbs. This makes them easier to spot especially during the morning. LEDs are also better than light bulbs and other type of lighting since they are fairly strong. They can take abuse from the ever-changing weather and even hitting. Their solid state casing in the LEDS are strong enough that it makes the lights shock proof and they would not be damaged even when dropped.
The use of Neon lights in led lighting for your car is also effective. Neon illuminating is cheap and it does not cause any hassle when it comes to other exterior parts of the car. Such forms of illumination are effective in the cars underbody and in the backside. The lights would actually turn on in the underbody of the car when the car passes the street. Aside from that, neon lighting can be used in the interior. The shift knobs can be designed with lighting strips. The neon can also be used as a customizer, making your plate number look more colorful. Lastly, the neon can be used in washers and in the backseat.
For LED barricade lights and LED lights for construction and industrial purposes, visit Brandon's Safety Lights.

How to Choose a Good Shower Panel

Are you sick and tired of your everyday basic shower system? A shower panel may be exactly what you need to spring life into your morning cleansing process. Shower panels can be bought in a variety of different sizes, materials, and functionality. Whether you are looking for a system that gives you a spa-like level of relaxation, or something to take your morning showers one-step above drudgery, there is a shower panel that will work well for you.
If you have the budget available, an excellent choice for a shower wall panel is one created by Platino. Made from stainless steel, you will love your taking showers (panel system responsible of course). So what is so great about the Platino system? Well, for one, it outputs water through four different mechanisms. The main showerhead outputs a relaxing waterfall great for days where you want to wash away.
It also features a hand held showerhead that enables you to clean the places of your body difficult to reach with the main showerhead. At the bottom of the shower panel, it has four jets of water for a soothing massage effect as well as a spout for filling up the tub. At $600, this system can be bit expensive. However, according to the reviews, it is well worth it.
To learn more about buying shower wall panels, you can check various resources online and locally. Great places to check for more information include Lowe's and Home Depot. In addition, of course, if you do not want to leave the comforts of your home, there are plenty of resources on the internet to look through.

What Is an Oat Crusher?

Oats often require grinding and crushing before they can be implemented as ingredients. This process occurs using oat crushers of various sizes. An oat crusher can turn grains into a fine powder. This powder is then sold to food manufacturers.
Function
Oat crushers grind and crush oats into a powder for cooking and baking purposes. Oat crushers may also be used to grind other grains, such as wheat and barley.
Types
There are many types of oat crushers, including those that are hand turned, automatic and windmill powered.
Antique
Antique oat crushers -- those which have been around for a hundred years or more -- have become prized collector's items.
view their website for more information :
Company name：Lipu Heavy Industry Co., Ltd.
Contact us：Phone: 86-21-68798918
　　　　　Fax: 86-21-68798919
Web site：http://www.mobilecrusher-china.com/
The main products：Granite Crushing Machines,Granite Crushing Screening Plant,Stone Mobile Crushing Plants,Ore Crushing Plant